Residential Drywall Installation in Argusville, ND | Clean Install
Argusville is a small city about 16 miles north of Fargo, spread across four square miles with plenty of room between homes. More than half of its houses went up during a building boom between 2004 and 2009, and many of those homes are now old enough for their first round of real drywall work: cracked corners, worn edges, settling lines, and rooms being finished or reworked for growing families. Fargo Elite Drywall installs and repairs drywall for homeowners across town, from a single damaged corner to a fully finished lower level.
A clean install is about the details you notice every day. Outside corners that run straight from floor to ceiling, outlet cutouts with no gaps around the cover plates, crisp lines where drywall meets windows, tile, and cabinets. Those edges decide whether a room looks finished, and they're where rushed work shows first. We take the time to get them right, using the right bead and trim for each spot, so the result looks sharp and holds up to everyday life.
Request a FREE Quote.
Get the numbers you need to plan with confidence—no pressure, just clear and honest pricing.
Straight Lines and a Tidy Site
Fargo Elite Drywall is based in Fargo, about 16 miles south of Argusville, close enough to keep a steady schedule and come back for anything that needs another look. We set every corner bead with a level, measure cutouts twice, and check our edges before calling any stage complete. Floors are covered, materials are kept organized, and the work area is cleaned at the end of each day. You'll get a clear quote, a crew that respects your home, and finished walls with lines as clean as the room deserves.
A Newspaper Name and a Housing Boom
Argusville was platted in 1881 when the railroad reached this point, and it most likely took its name from a local newspaper, the Daily Argus. A post office opened the same year and served the town for just over a century before closing in 1982. For most of the 20th century, the town stayed tiny, with between about 115 and 160 residents from 1930 through 2000. The former Argusville High School building was demolished in 2023.
Then came the boom. Between 2004 and 2009, a wave of new construction more than doubled the town's housing, from 65 units in 2000 to 152 in 2010, and the population jumped from 147 to 475. The town changed almost overnight. The median age dropped from 40 to 31.7, average household size rose from 2.37 to 3.15, and by 2010 nearly 39 percent of residents were under 18. The 2020 census counted 480 people, so the population has held close to its post-boom size.
Clean Lines Start at the Corners
Outside corners are the most visible edges in any room and the ones that take the most abuse. Corner bead comes in several types: nail-on metal, paper-faced metal or plastic bedded in compound, vinyl, flexible bead for curves, and rounded bullnose. In homes around 15 to 20 years old, a common problem is bead that has started to crack along its edge or pull loose after years of bumps and seasonal movement. Patching over it rarely lasts. The better fix is to cut out the failing section and install new bead bonded with compound along its full length.
Transitions matter just as much. Where drywall meets a window, a tub surround, a stone fireplace, or a cabinet run, the edge needs a deliberate finish. That might be a J-bead or L-bead trim that gives drywall a clean, factory-made edge, a tight joint to tile backer that's taped and finished smooth, or a small reveal that keeps two materials from rubbing. Cutouts for outlets, switches, and lights are cut so cover plates sit flat with no gaps showing. These details take extra time, and they're what separates a clean install from one that only looks done from across the room.
Boom-Era Homes, 15 to 20 Years In
With more than half of the town's housing built in the same five-year window, many homes here are reaching the same stage at the same time. Common signs include hairline cracks running up from the corners of doors and windows, cracked or chipped outside corners, and faint tape lines in bathrooms where steam has worked on the joints for years. None of these mean something is seriously wrong. They're normal wear for walls of this age, and they're easiest to fix properly before they spread.
Households here also put corners to the test. In 2010, nearly 59 percent of households had children at home, one of the highest shares among the towns we serve. Hallways, stairways, and play areas see bikes, toys, and running kids, so we steer those spots toward paper-faced bead bonded in compound, which resists denting and cracking better than nail-on metal. Some families choose rounded bullnose corners in play areas, since a rounded edge chips less and is gentler on small heads.
How We Deliver a Clean Install in Argusville
A clean install comes from paying as much attention to edges, joints, and openings as to the flat parts of the wall. Here's how we handle a project from first look to final inspection, with the local details we plan around. Each step is built to leave lines straight and transitions crisp.
Step 1: A Walkthrough Focused on the Details
We start by looking closely at the edges in your rooms. We check outside corners for cracks, dents, and loose bead, look at the joints around windows, doors, and tub surrounds, and note any cutouts with gaps around cover plates. For new work, we measure each wall and ceiling and mark every opening, fixture, and transition to another material.
In homes from the 2004–2009 boom, we also look for patterns: cracks that repeat above the same doors in each room, bead failing on the same type of corner, or bathroom joints showing through paint. A pattern often points to the cause, like a missing line of fasteners or poor bathroom ventilation, so the repair can address it. You'll leave the visit knowing what we'd fix, how, and why.
Step 2: Choosing Bead, Trim and Materials
Your quote lists the work room by room, along with the specific bead and trim for each spot: paper-faced bead for high-traffic corners, J-bead or L-bead where drywall meets windows or tile, and bullnose if you'd like rounded corners. Board types are noted too, including moisture-resistant panels for bathrooms. If the project needs a permit or inspection through the City of Argusville, we'll confirm that and plan around it.
We'll walk you through the choices so they fit how your household uses each room. In a home with young kids, the corners along a busy hallway may get a different bead than those in a formal dining room. Once the plan is set, you'll get a schedule showing which rooms will be worked on each day and when the dusty and noisy stages will happen.
Step 3: Protection and Precise Removal
Before anything is cut, floors are covered, nearby furniture is moved or wrapped, and the work area is closed off with plastic. Failing corner bead and damaged sections of board are removed with clean, straight cuts, so the repair has crisp edges to work from instead of torn, ragged ones. Fasteners are pulled, and loose paper is trimmed back to solid material.
With homes spread across about four square miles, most properties here have room for a truck to park close to the door, so materials come in quickly and cleanly. We carry board in along a protected path, bag scraps as we go, and stage tools and materials in one spot so the rest of your home stays clear. Debris leaves with us at the end of the day.
Step 4: Hanging With Tight Fits and Straight Edges
New board is cut to fit tight, with factory edges placed at outside corners wherever possible so bead has a straight, solid edge to sit against. Outlet, switch, and light cutouts are measured from fixed reference points and cut precisely, which keeps cover plates flat and avoids patching around boxes later. Screws along edges that bead will cover are set just below the surface so the bead seats flat.
Where drywall meets other materials, we plan the edge before hanging. Board stops at a consistent distance from window jambs, tub flanges, and stone so the trim or bead can finish it cleanly. Bathrooms and kitchens tend to be among the first rooms updated in a house of this age, and that's where these transitions come up most. Getting them right at this stage makes the finishing cleaner and faster.
Step 5: Setting Bead and Finishing the Edges
Corner bead goes on with a level so every outside corner runs plumb from floor to ceiling. Paper-faced bead is bedded in compound, pressed tight, and wiped down so it bonds along its full length. J-bead and L-bead trims are set straight against windows, tile, and stone. Inside corners are taped with folded paper tape, and each side is finished separately so both stay crisp.
Joints and bead flanges are built up and feathered in thin coats until they blend into the wall. In bathrooms where steam has caused trouble before, we use moisture-resistant board and careful taping so the joints stay hidden. Every edge is checked along its length with a straightedge and a work light before the final coat dries. A wavy corner or a ridge beside a window is the first thing the eye catches.
Step 6: Detail Inspection and a Clean Handoff
When finishing is done, we inspect every corner, cutout, and transition, sighting down each outside corner and checking each cover plate opening. Anything that isn't crisp gets another pass. Then the work area is cleaned, the plastic comes down, and floors and surfaces are vacuumed and wiped.
The town most likely takes its name from the Daily Argus newspaper, and the word itself goes back to Argus, the hundred-eyed watchman of Greek myth. That's a fitting standard for a final inspection: nothing gets past without a close look. We walk the rooms with you, point out the repairs and new edges, and leave you with walls ready for paint and lines that stay clean for years.
Get Your Drywall Project on the Calendar
Tell us about the rooms you want finished, repaired, or rebuilt, and we'll set up a time to see the space in person. You'll get a clear written quote covering materials, finish level, and cleanup, along with a schedule you can plan your week around. Fargo Elite Drywall serves homeowners in Fargo and the surrounding communities on both sides of the Red River.